development stuck/still alive?

Moderators: Voyager, BertB, rtenklooster, Stuntteam

Post Reply
Message
Author
passie
Normal user
Posts: 19
Joined: 18 Mar 2017, 07:27

development stuck/still alive?

#1 Post by passie » 30 May 2019, 00:26

The latest firmware release is from 18 OCTOBER 2017
The latest message on www.rflink.nl is from 23 AUGUST 2018

is the development and the RFlink board still alive?

Could be that i'm impatience and have to wait a bit longer 8-)

regards,
Passie

Voyager
Normal user
Posts: 59
Joined: 15 Apr 2015, 14:25

Re: development stuck/still alive?

#2 Post by Voyager » 30 May 2019, 00:28

Yes, you have to wait a bit longer.. :)

shyriu42
Normal user
Posts: 6
Joined: 24 Feb 2019, 14:38

Re: development stuck/still alive?

#3 Post by shyriu42 » 30 May 2019, 00:51

i think all is dead



no answers from forum no answers from email no answers to help ...


it s very unfair from the man/group who initiated this project to to drop those who have invested time and money in a rflink and feel alone in the world. without the ability to have the source code that could be taken over by others. To have stopped a free project like this one and to deprive everyone of having new is simply .... disgusting i don't understand a so long silence.


really i send many emails without answers.

User avatar
Stuntteam
Site Beheer
Posts: 601
Joined: 27 Jan 2016, 16:46

Re: development stuck/still alive?

#4 Post by Stuntteam » 30 May 2019, 10:13

>no answers from forum no answers from email no answers to help ...

You send at least 4 messages about an elepowstar doorbel... and not all of them that friendly.
You even received an answer that we are looking into it.

>it s very unfair from the man/group who initiated this project to to drop those who have invested time and money in a rflink

The minimal cost to get rflink working is around 7 euros (arduino+decent rf module)
The project is all free, this also means there is no big customer support team available to answer 4 doorbell messages. Time to answer mails means less time for development.
There is a list of devices that are supported. If you select a doorbell from that list (and they are available as low as 5 euros) you are fine.
Also, I am pretty sure that the invested time from this side is A LOT higher than your invested time and money.

>To have stopped a free project like this one and to deprive everyone of having new is simply .... disgusting i don't understand a so long silence.
The project has not stopped. However, you are free to use any other solution...Buy something expensive and see what you get with your complaints and negativity.
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

shyriu42
Normal user
Posts: 6
Joined: 24 Feb 2019, 14:38

Re: development stuck/still alive?

#5 Post by shyriu42 » 01 Jun 2019, 18:12

hi
thanks to answer me, you are right and i m really sorry to my impatience but i m not programmer and i have no mind about the time to search and made a plugin or other. Why it's so long since 2017 ? and why my doorbell can be activated by a rflink command. I have no idea about the time and works needed to do it and after 2 ou 3 month i m impatiently. sorry


ps: you are right and you answer to me 1 time that you works on it..

Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests