Difference between revisions of "NEXTIONDisplay"

From Let's Control It
Jump to navigation Jump to search
Line 17: Line 17:
 
<span style="color:red">
 
<span style="color:red">
  
   LCD ESP-01
+
   LCD ESP
 
   GND GND
 
   GND GND
 
   VCC    VCC
 
   VCC    VCC
   SDA GPIO 0
+
   Tx GPIO port acting as Rx
   SCL GPIO 2
+
   Rx GPIO port acting as Tx
  
Some displays feature a Reset or RST pin. At start-up those displays may show noisy pixels.
+
In order to get those displays to work properly you need to activate the pull-up of the Tx pin. A quick test is to set the pin to high (1) but for long turn you should enable the pull-up instead. If the pin is missing a pull-up you can add one yourself by soldering a 10k resistor from 3.3V to the pin.
Resetting the display and thereafter the ESP will help.
 
NodeMCU for instance, provides a RST pin. Connecting this pin to the RST pin of the OLED is a good way to synchronize operation.
 
 
 
Other displays might already be connected to a ESP board. Many of these displays have their reset pin connected to a GPIO. Commonly the pin number 16 is used and in order to get those displays to work properly you need to activate the pull-up for that pin. A quick test is to set the pin to high (1) but for long turn you should enable the pull-up instead. If the pin is missing a pull-up you can add one yourself by soldering a 10k resistor from 3.3V to the pin.
 
  
 
= ESP Easy =
 
= ESP Easy =

Revision as of 13:08, 21 May 2018

Introduction

The ESP8266 module can be used to control an Serial Nextion Display. Due to its on-board intelligence and the presence of a touch panel, the display can be used to control devices.

Nextion2.jpg

Hardware

The board is connected to a controller by means of 4 wires

Nextion2.jpg

Connect the Nextion Display to a serial port and to +5 V and ground. The Nextion software module provides the use of a Software Serial port. So, it is not required to use the 'native'Tx and Rx ports of the controller. This display works with 5V and can be connected directly to the ESP module.

Connections

 LCD 	 	ESP
 GND 	 	GND
 VCC    	VCC
 Tx		GPIO port acting as Rx
 Rx		GPIO port acting as Tx

In order to get those displays to work properly you need to activate the pull-up of the Tx pin. A quick test is to set the pin to high (1) but for long turn you should enable the pull-up instead. If the pin is missing a pull-up you can add one yourself by soldering a 10k resistor from 3.3V to the pin.

ESP Easy

Use the device tab on the ESP Easy webinterface and create a new task by editing one of the available tasks. Select "Display - OLED 1306" from the dropdown box.

Enter template texts into lines 1 to 8. Plain text will be shown on the display exactly as entered. If you want to show a value, enclose <task name> and <value name> between brackets, separated by a hashtag.

So if you have a dallas sensor running, with taskname "Dallas", to get the temperature value, use this:

 [Dallas#Temperature]

With release 057, some features were added. If you put %sysname% or %ip% or %systime% on a line in the table, the display will show either the name you gave the ESP module, its IP address or its time. The latter only when NTP is being deployed.


Check this sample on how to get it done:

EasyConfigOLED.png


(The IDX field will be stuffed with '1', because it's needs a value. But nothing will be send with this device)

Commands

Command Value Extra information
OLED,<row>,<col>,<text> - Write text messages to OLED screen, ROW for row, COL for starting column, and Text for text.
OLEDCMD,<value> on, off, clear Switch on or off the OLED or to clear the display. During the off state, the content will be updated according to the latest values or states.

Special characters

Name Character Code (generic) Code (html) Code (verbose) Extra information
Degree ˚ {D} &deg; degreeC
degree_C
"degreeC" and "degree_C" will give you ˚C
Angle quotes (L/R) «
»
{<<}
{>>}
&laquo;
&raquo;
- -
Greek mu µ {u} &micro; - -
Currency
¥
£
¢
{E}
{Y}
{P}
{c}
&euro;
&yen;
&pound;
&cent;
- -
Math symbols x¹
x²
x³
¼
½
¾
±
×
÷
{^1}
{^2}
{^3}
{1_4}
{1_2}
{3_4}
{+-}
{x}
{..}
&sup1;
&sup2;
&sup3;
&frac14;
&frac12;
&frac34;
&plusmn;
&times;
&divide;
- -