Let's Control It

toffel969

livebelive wrote: ↑10 May 2017, 06:32 The problem has been solved！！！
Device[deviceCount].VType = SENSOR_TYPE_TRIPLE; this place needs to be replaced
Device[deviceCount].VType = SENSOR_TYPE_SINGLE;

very good ! Glad to hear you were succesful !

toffel969

Unit: 12 GIT version: v2.0.0-dev8
Local Time: 2017-05-09 19:30 Uptime: 2 days 18 hours 50 minutes
Load: 10% (LC=26397) Free Mem: 21840 (28520)

toffel969

@krikk I see you started something on the wiki. I edited it a little bit. I think we can keep the table on the main wiki and link the devices there. I like the edit you did. I think also sensors should be listed in a table, the way it is presented now is very cluttered. I also think we need to move...

toffel969

somebody help me!!! First of all, stop stressing! If you want to get help here, you need to be patient and polite. Then checkout the CO2-Sensor on the wiki. It also uses serial communication. You will have to develop a plugin from there. It uses the softserial library to provide serial communicatio...

toffel969

grovkillen wrote: ↑09 May 2017, 09:52 It's now live on the wiki: Wiki: Dew Point for temp/humidity sensors

very good, thanks

toffel969

Hi... on this forum you will find information about ESP Easy and RFLink. Starting point is www.letscontrolit.com. This will also point to the webshop. Information about Domoticz can be found in the forum and Wiki specifically for Domoticz: http://www.domoticz.com/forum/ and http://www.domoticz.com/...

toffel969

Over time I have repeatedly struggled trying to reset an ESP unit. When the unit is factory new, there is no problem. But once it has been flashed and something is wrong it becomes difficult. It seems that some info is retained after a new flash, and some aren't I found that it sometimes helps to f...

toffel969

Have you seen the ser2net plugin? It should be the one for your application. I think it will require lua scripts on the domoticz side as it just maps the serial to a TCP port. Yes, see the ser2net plug-in, set to complete, do not know how to send or receive data. Can you teach me how to do it? No, ...

toffel969

@krikk
I see you started something on the wiki. I edited it a little bit. I think we can keep the table on the main wiki and link the devices there.

toffel969

My English is so bad don't laugh at me Please！！！Thanks！ The problem is this I got a voice recognition module I want to connect this module with espeasy What I want to do is to read the data from the module, and then transfer it to domoticz via espeasy There are two options 1, through the espeasy to...

toffel969

hmm... interesting (Spock would say "fascinating"..) Did you re-download the dev8 or is it the same file as before? Would be the easiest explanation. Regards Shardan. I didnt reflash between the crashes. So its still the very same version that malfunctioned Unit: 12 GIT version: v2.0.0-de...

toffel969

I support your cause and will try to contribute. Can I suggest that we make a table similiar to the input/output devices and include useful information in the table. I would like us to brainstorm which info that could be. To start the process i would suggest: 1. ESP chip version of the device (like ...

toffel969

After the last crash I just restarted the node. Unit: 12 GIT version: v2.0.0-dev8 Local Time: 2017-05-08 12:23 Uptime: 1 days 11 hours 57 minutes Load: 8% (LC=26666) Free Mem: 21656 (28520) Now its starting to get weird. I am running with a 60 second delay. So maybe it wasn't the controller bug afte...

toffel969

it does not matter which firmware you flashs, if you open a high-voltage device like the sonoff devices, you have to know what you do... yes we should include a warning, but i see no reason to "exclude" this device. ...what i noticed when looking on the espurna site is, that we still have...

toffel969

my thoughts on this: why do we waste resouces the develop 2 different firmwares instead of one?? ...why did he develup espurna when there was espeasy already (or the other way around)? wouldn't one firmware which solves all, much better for the enduser... ...and are we here at the espeasy forum or ...

toffel969

I'm helping a curling club with this and that and they wanted to have the dew point monitored. In general they use this to know how to proceed with the ice making. Anyhow, I found out a way to calculate this within ESPeasy. Heres how I did it. First of I hooked up two BME280. This is possible due t...

toffel969

Nice job! I'm using it with a .96 Oled right now; the Wemos 96x48 disp and with a bit of cheating I managed to make it fit to my needs so thanks a lot. Any intention to adapt it to other Oled like the Wemos shield and the new 32x128 one ? If not I'll try to monkey with the code to the best of my kn...

toffel969

This is how I want it to do: https://www.uploadarchief.net:443/files/download/rotary%20encoder.gif Below is the switch state of the Rotary-encoder. https://www.uploadarchief.net:443/files/download/rotary-encoder-fasering.jpg If I read input A then check what is the status of input B is. Then I know...

toffel969

maybe i jumped the gun. last night at 0:00 i checked again and the webserver was not responding. it was still reporting sensor data to domoticz and responding to pings. i also managed to reboot it via http , but webserver was definitly not working anymore. however after reboot it has now 9h uptime a...

toffel969

GIT version: v2.0.0-dev8
Local Time: 2017-05-06 21:55
Uptime: 0 days 9 hours 18 minutes
Load: 10% (LC=26251)
Free Mem: 21472 (28520)

still going strong. maybe psy0orz has an explanation. next would be dev 7 though im thinking thats a bit pointless

toffel969

I flashed the dev-dev8 version. It just continues to work and send values to Domoticz. Now running for 1h stable , web interface is responsive, Data is reported to Domoticz. Free Mem: 21840 (28520) With the previous bug, it would have stopped working quite some time ago. Now I am not sure if the pro...

toffel969

wemos d1 r2 is also very good for started, but seems like wemos does no longer sell them: https://www.aliexpress.com/item/WeMos-D1-R2-V2-1-0-WiFi-uno-based-ESP8266-for-arduino-nodemcu-Compatible/32757865666.html Yes true, it also has remarkable V-Inputrange and provides 5V strong enough to drive re...

toffel969

https://www.letscontrolit.com/wiki/index.php/LevelControl The documentation about the plugin assumes that the gpio/relay will be ON below the target temperature +0.5 hysteresis etc. - (heating regime) Is it possible to reverse the logic i.e. gpio/relay OFF when below and ON when above? - (that will...

toffel969

Hi Guys, TL;DR: Homeseer let me down by removing their licensing server thus preventing my highly paid home automation system to work, at least the part using the RFXCOM. So I swapped to Domoticz and being an Arduino fan I naturally explored the Wemos and learned about the community here. ---------...

toffel969

Hi everyone. I'm fairly new to espeasy and esp8266. I have. 6 sonoff switches loaded with espeasy using mqtt with openhab. They work flawlessly with espeasy and I'm really happy with them. Not I have switches working I would like to create a thermostat that will turn my boiler on and off. Does anyo...

toffel969

Unfortunately, when sunlight is shining on the sensor, it still triggers permanently. In think this is immanent to PIR type devices (passive infrared) . if the ir intensity changes it will trigger. Leaves it too indoor use case or if you only want to use it when its dark... To me it seems more like...

toffel969

Would be interesting indeed. Regards Shardan Update: Uptime: 0 days 15 hours 57 minutes Free Mem: 21408 (11720) still going strong. I consider this working and will now try to flash dev-dev8 to see if "this unknown sniplet of code ;-)" (at least to me) fixes the problem with the controlle...

toffel969

Thanks for testing. Check the free RAM on the webside, it should not decrease over time. Regards Shardan After 2h30 operation Free Mem: 22064 (11720) so far stable and reporting values to domoticz. So it seems to be working. If I feel adventurous I will try to flash dev8 back tomorrow morning. Gege...

toffel969

You're welcome :) Correction to above post... I flashed the wrong node :cry: :D it was still running RC147, so no wonder I lost the devices and settings. However now I flashed the correct node, it didn't reset the settings. Now on the correct node I can also find my sensors :). Its reporting the da...

toffel969

Here you go. This is the version i used for bulk testing, it is running on nodeMCU and WeMos for around 2 days without issues. It is compiled with the "normal" option, so no testing or development parts are compiled in. firmware_normal4096.zip . Anyone who wants to use it: This is NOT an ...

toffel969

Yes please! ;-) A 4096-memsized one? Or do you need another flashsize? Regards Shardan Yes a 4096-mesized. Target node is a Wemos D1 mini pro with 2 D18B20 Temperature probes, 4 buttons, analog soil moisture probe and an SSR connected directly to GPIO as output actuator. regards Sebastian

toffel969

9600 bps is not the standard console port speed. Try with 115200, it should work fine. There is no issue in powering a Sonoff from the 5V line from an FTDI adapter, works well. And I can see that you have correctly set the data signals to 3.3V on the FTDI adapter, which is the good thing to do. Let...

toffel969

Hi, I am running v2.0.0-dev8 on multiple Sonoff S20s using 'ESPEasy_v2.0.0-dev8_normal_1024.bin'. When trying to do an OTA with the same file, i get an 'Update Failed', and the device reboots with all settings reset. Is this a bug, or will OTA not be possible on 1M devices in the future? CherAlban ...

toffel969

I too had hardware issues with a couple of NodeMCU v1.0 boards. Really bad soldering leaving open lines instead of good connections. I had to resort to some jumper wire to close the connections as soldering would have been too difficult. Never had a problem with any of the Wemos devices, There are ...

toffel969

MortenEV wrote: ↑04 May 2017, 22:50
Shardan wrote: ↑04 May 2017, 21:40 Is it a cheap FTDI progger (around 2..3 USD) ?

Yes, it is a cheap one. Which one from ebay ( or other) source will be a better model ?

Afaik cheap one should be OK, but u need another power supply. Don't power it through ac... T dangerous.

toffel969

Yes please!

toffel969

Yes I can do that. Is it included in the dev8 ? If yes I would just need to make one of my nodes report to domoticz instead of standalone. If no could I kindly ask you to provide me with the relevant 4mbbin file?

toffel969

Hello all, for testing a fix i've used several nodeMCU's. This lead to a bulk quality test of these boards as i run in several problems. I've used two different versions, the older one with CP2102 as USB-TTL converter (a white back label says "AMICA" for brand) and a newer version with a ...

toffel969

Hi All, For some cases (especially when playing with rules) I had the problem that I could not get any wireless access to the ESP8266 anymore. I needed to unmount the ESP from the location to be able to put it close to the PC again and re-flash or (factory-)reset it via the serial port. My idea is ...

toffel969

Thanks Krikk That works fine , but my arduino is now being a lot busy receiving all that data input is there a way to display the results only when i need them by sending a command maybe the values are stored in a variable on the esp is there a way to display that variable example : print Humidity ...

toffel969

As a regular visitor to the Western Cape, a special warm welcome for you. EspEasy will definilty help you to achieve what you want much faster

toffel969

hi people, Is with very pleased to see the development of this good project, which has brought a economic and intuitive fresh air in the area IOT. With this also benefiting from the equipment comes to the end users that do not need advanced knowledge of electronics. But any project has to have a go...

toffel969

Thank you, I know how to use i2c. I was just curious since I got values > 0 on the sonoff. If you want to use the ADC of a Sonoff switch you have to modify the source and compile it yourself. Look for this line in the main program module: #define FEATURE_ADC_VCC false and change false to true. That...

toffel969

chunter1 wrote: ↑02 May 2017, 12:40 Unfortunately, when sunlight is shining on the sensor, it still triggers permanently.

In think this is immanent to PIR type devices (passive infrared) . if the ir intensity changes it will trigger.
Leaves it too indoor use case or if you only want to use it when its dark...

toffel969

Last month we made some great progress with ESPEasy version 2.0. If you look at this link you can see many things have happend: https://github.com/letscontrolit/ESPEasy/pulse/monthly We've merged 33 pull requests containing 100's of improvements and fixes. Also we've closed 20 issues on the issue t...

toffel969

data wrote: ↑02 May 2017, 22:04 So, this means it is 'receiving' approx. 0.1V noise?!

No according to your post it is rather 0.05v as a0 of esp is 0-1V only. Wemos and nodemcu have voltage deviders to reduce 3.3v to 1v

toffel969

So, this means it is 'receiving' approx. 0.1V noise?! Yes, the pin is definitely not connected, I opened it. There are no traces going to the a0 of esp chip. If you need analog on sonoff u need to be either be a soldering guru (soldering to chip) or use the i2c analog expander (see wiki). You can s...

toffel969

Hardware: Sonoff WIFI (without 433MHz module) Software: ESP Easy Version v2.0.0-dev7 I have configured a device as 'Analog Input' and it gives me readings between 31 and 38 throughout the day. Since the device is supposed to run on 3.3V, my guess is, that this is Vcc * 10? As the device is in use, ...

toffel969

Hello, Wehre can I compile? Do you have an example for the formula? Thank you Best regards In order to compile, you have to download the source files, modify them and then compile them in the ArduinoIDE. There is a tutorial in the wiki There is however a simpler solution to your problem; rules :- 1...

toffel969

The sensor i used has it's own voltage regulator from 5...15 Volts to 3,3V. i can't say what the small sensors use, i didn't test them yet. The PIR's with their own regulator will not work easily with 3,3V as the regulator needs some volts for itself to work. This so called "Drop Out Voltage&q...

Search found 469 matches