Hello Thomas,
as you describe it works.

Thanks for your effort

Christof

Thanks for support and help

Hi
my first controller is an OpenHAB MQTT.
So far that's right. I can also switch a GPIO via MQTT.

What must the command for the Nextion Modul look like?

Hello,
with http://192.168.2.69/control?cmd=NEXTION ... txt="Hallo "
can I write in the text field t.2, on Page0, the text Hello.
How can I realize this via MQTT?
This is my config from the ESP

Best regards

Hello
I have the same problem.

Look here:

http://www.letscontrolit.com/forum/view ... 869#p24927

Best regards

Hi Lisa I flashed the upyeasy_v021_20180218_test_esp32_2048.bin on the ESP. Unfortunately, the ESP now boots in an endless loop. The serial monitor displays: rst: 0x10 (RTCWDT_RTC_RESET), boot: 0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP: 0xee clk_drv: 0x00, q_drv: 0x00, d_drv: 0x00, cs0_drv: 0x0...

Traceback (most recent call last): File "<stdin>", line 1, in <module> File "upyeasy / __ init__.py", line 56, in main File "picoweb / __ init__.py", line 275, in run File "uasyncio / core.py", line 138, in run_forever File "uasyncio / core.py", lin...

>>> import upyeasy
>>> upyeasy.main()

It is working

Best regards

Hi Lisa Enclosed a feedback to the version v53 Uptime is displayed incorrectly: Uptime: -1 days 0 hours 0 minutes After configuring a BME280, the ESP32 can no longer be reached via browser. The serial monitor says: 568478250.503 <HTTPRequest object at 3ffc0570> <StreamWriter <socket >> "POST / ...

Hi Lisa, with me the firmware (upyeasy-esp32.zip) from the first post does not work either. (Hardware is a doit.am v1 devkit). The adapted 2 MB version works. When I set up an MQTT server on the controllers side and press SUBMIT, I get the message "Error: Connection interrupted" in the bro...

Hi Lisa
your help worked.
But after a reboot the settings are lost.
Best regards

Hi Lisa I tried your trick. But unfortunately without success Here is the result: >>> import upyeasy ? [0; 32mI (99442) modsocket: Initializing? [0m >>> upyeasy.setwifi ('SSID', 'PASSSWORD', 'BACKUPSSID', 'BACKUPPW') Traceback (most recent call last): File "<stdin>", line 1, in <module> Fi...

Hi Lisa with the new firmware for the ESP32, the WIFI configuration does not work anymore. The following error message comes. >>> upyeasy.setwifi('SSID', 'PASSSWORD','BACKUPSSID', 'BACKUPPW') Traceback (most recent call last): File "<stdin>", line 1, in <module> NameError: name 'upyeasy' i...

There is something wrong with the adjustment of the _C001.ino + _C002.ino + Misc.ino regarding "getBearing".
Can the programmer look and repair this friendly?
Best regards

I have the same problem.

I also have the problem that the ESP have connected to a DHT22 or DS18B20 repeatedly perform a reboot. Without sensor no reboot.

If the ESP chip ID clearly? If so, then the software could put the last 4 digits of the ESP chip ID as UNIT number. Thus, the problem should be solved. Would it be possible?

Hi Martinus,
The reference to the unit numbers was the solution. Thank you, I had already spent a lot of time troubleshooting.
In WiKi I find this nothing. Where can I read the individual settings and their meaning?

Hi I have the following problem with MQTT. The following ESP versions I use: ESP-01 NodeMcu V 3 ESP ADC ESP12-E I would like to send all 4 ESP s the sensor values for MQTT broker. The broker is running on a Raspberry Pi 2 Quad Core All ESP s run stable without the use of MQTT. In one ESP with MQTT P...

I have the same problem as VMFS 1968 describes.
it looks as if the measurement is divided by 2

The same effect also applies to the OLED display.
In the version R59 the error was already present.

another GPIO I have already tested without success
How does the reset command from the serial Interace?

Hi

The voltage is 3.5 volts
The resistance between VCC and the Data pin is 4.7K

Hello I use the R57 version. Also in the previous versions of the problem occurred. On GPIO 14 I have a DHT 22 sensor is connected. Unfortunately only 11,20 appear to temperature. Hygro is 29.3%. The values correspond to about half the correct values Why is that? What could be the problem? A 18B20 s...