Hello.
I saw that atom.io is no longer supported.
now i wanted to activate some unofficial plugins with vsc in esp32.
since I did it under atom.io a long time ago, I don't remember how it worked.
I hope someone can help me.

Regards

Good day I will use this motor driver for the project. DollaTek 7A 160W L298 PWM Speed Controller Dual DC Motor Drive Module https://www.amazon.de/DollaTek-Speed Controller-Motor-Drive-Modul/dp/B099DRSL45/ref=sr_1_14?keywords=L298+Motor+Controller&qid=1674129927&sr=8-14 Alternatively, one co...

I'll test tomorrow what kind of current is actually flowing.
Without burden and with burden.

TD - thanks for the help I have 2 of these linear actuators. https://www.vevor.de/linearantrieb-c_11633/linear-actuator-motor-250mm-6000n-12v-hubmotor-elektromotor-linearantrieb-p_010891954738?v_tag=ec010510-9749-11ed-bcaa-7fbbf4f7936e.3 I just want to flip the modules. A shunt to protect against ov...

Many thanks for the quick response.

The position is to be monitored by means of the gyro sensor.
The wind should be monitored with an anemometer.

If the power fails, the system is powered by a battery that is charged by solar.

If the mechanics are blocked, this is monitored by a gyro

Hello I would like to build a solar tracker for 2 solar panels each driven by an actuator. The whole should be on a flat roof. The engines are to be powered by an L298n. The voltage should be 12 v to use the voltage converter from the L298n for an ESP32. The angle of the solar modules is to be monit...

Hello I was able to use part of the sensor. Unfortunately, the gloss wasn't read correctly. The other problem was that I couldn't reliably integrate the sensor. First I have to press the button several times. It seems more of a coincidence than a methodology. Maybe there is firmware for the sensor t...

I only applied 3.3v voltage to the sensor. Actually, after supplying the sensor with voltage, it should recognize whether the I2C bus is present. If so, the bus will do. If not, it goes into stand alone mode. But I don't know whether the firmware on the Attiny 44 supports it. It seems to work with t...

Hello Many thanks for the answer. Unfortunately, I don't get a device displayed under i2c scan. I've tried with d1 and d2 pin. I haven't had any success with d4 and d8 pin either. 10 kOhm resistors are soldered. Now I have connected an i2c display to d1 and d2 for the test. The display was recognize...

Hello everybody I have now added a 10K Ohm resistor for each SDA SCL on the sensor. Unfortunately I have no connection with it either. My sensor is this https://wemakethings.net/chirp/ . When I run the example code on an Arduino Mega I get values. So the sensor seems to go by itself. I get 1 as the ...

Hello
Thank you for your reply.
I have now with D8-SDA and D4 SDL under i2c scan Unknown error at address 0x1 to Unknown error at address 0x7F.
Do I have to change the speed of the bus?

Many thanks for the help
André

Hello I'm trying to connect the Plant Watering Alarm Sensor to a Wemos D1. Unfortunately, the i2c scan does not show any device. do I still have to flash the sensor? If so, does someone have a suitable hex file? I use a "my smartUSB light" stick for flashing. I hope someone can help me. Do...

Hello I rebuilt the LCD screen and placed the buttons on the A outputs. Unfortunately I still have 2 problems. 1. If I have connected the flow sensor to the ESP, it does not boot. The sensor is connected to the GPIO o. ". Problem. When I switch the solid state relay it opens, but when I switch ...

Thanks for the information.

I'd rather use the buttons right away. I will also install an LCD I2C module to save connections.
I'm trying to build it today and then send a few pictures.

Many thanks for the help.

greetings
André

Hello TD-er Many thanks for the answer. I would like to switch the valve with a solid-state relay. I found something else for the LCD screen. The keys are queried with A0. Different resistors go to GND are installed for each button. Down 580 Up 230 Left 900 Right 0 Select 1200 Could the analog input...

Hello I have several questions for the Espeasy community. I would like to take a flow measurement for a canister to be filled. For this I got myself a solenoid valve and a flow meter. I still have an LCD Keypad Shield with me, which would be perfect. When the first canister is filled, I would like t...

Hello

I have a room humidity device.
At this I have now installed an ESP8266 with RelayBoard and DHT 11.
Firmware installed and everything is ready.
Now my problem.
Is there a timer?
I just want to run the humidification during the day.

Greetings André

Hello

I wanted to ask if there is already a code for the AS 3936 lightning Detecor.
I ended up laying down to experiment.

Best regards

André

Hello Thanks for the information regarding the ESP32 and the WS2812. It seems like the ESP32 is "too new" for ESPeasy. I have already created a version with Candle. Unfortunately, then no LED speaks. In the new version, there is also a possibility of GPS coordinates to enter similar to Tas...

Hello I tried to implement the plugin NeopixlBusFX into an up-to-date version of Mega ESPEASY. Unfortunately, I always get error messages when building ATOM. I currently have an ESP32 with 20100 version running. Unfortunately, the module Candle does not work there. I have tried several Gpio but have...

Hello I've got it now. I have set the comma there had not happened yet. Then I connected the LED GNG to PWM and V + to V + connected then it went. Before, I had V + (LED) to PWM (board) and GND (LED) to GND (board). Now I have to "only" still FHEM to bring the slider to control the LED. Th...

Hello I have a problem with the PCA 9685 module. The module is recognized in the I2C list under the address 0x40. When I try to control a port nothing happens. I have it with http: // http: //192.168.1.157/control? Cmd = pcapwm, 1.4095 tries. Or under the menu tool the comand pcapwm, 2.4095. Nothing...