Let's Control It

BertB

Hi all,

Is there some update on this question?
Will there be an update for the Domoticz capable OTA version for the Sonoff 4?

BertB

It has a small enough footprint to fit in a ESP8285 that is mounted in some Sonoff devices.
The Domoticz variant makes it integrate with Domoticz.

BertB

Good to hear, thanks.

BertB

Hi all, Thank you, first of all thanks for all the good work. I still have a question with respect to the update possibility of my Sonoff 4. I noticed that only FHEM versions with OTA are available (the ESP_Easy_mega_20210802_minimal_core_274_ESP8285_1M_OTA_FHEM_HA.bin) Is there any chance that the ...

BertB

I guess that means that a solution for that problem is to be found, but not imminent to happen soon?

BertB

Hi all,

I noticed that there are no bin updates for ESP_Easy_mega_20210114_minimal_core_274_sdk3_ESP8285_1M_OTA_Domoticz lately.
Is that going to stay?

BertB

Since the late-december releases of ESPEasy there are again OTA builds available that allow to OTA-update in a 2-step process on 1MB units (TD-er spent a lot of effort to realize this). Also 2 ESP8285 releases are there (with Domoticz or FHEM support). It is very hard to determine the type of .bin ...

BertB

This is very helpful, but I am not there yet. The values I obtain with MQTT device, are the svalue bits in the JSON string. The come like 1234567, but I want to show them as 1234.567. I cannot simply divide, because the values are in string format. On the other hand, I would like to sum two values. ...

BertB

Hi, I have a P1 gatway that sends information to Domoticz to a device I named Energy. I created also a node red script that is subscribed to domoticz/out. It receives the packages from Energy, but te data I need is in svalue format "Battery: 255 RSSI: 12 description: "" dtype: "P...

BertB

Okay, thanks

BertB

Last releases have no support for the ESP8285OTA.
I use that for my Sonoff 4ch.

Is the support on hold or ended?

BertB

Thank you for your answer.
I will ask Domoticz again how to proceed.
The meter guy probably will not return to reset the meter, I think.

BertB

I use the P1 wifi gateway as a sensor to Domoticz for quite some time. That worked very well up untill i got a new gas meter earlier this week. The new meter does not show up in Domoticz. All i see is the old meter, which also appears in the smart meter, next to the new gas meter. One of the Domotic...

BertB

Hi, I noticed the absense of ESP8285_1M_OTA in the releases lately. I do have a Sonos 4 chanel switch box, that is almost impossible to update without using OTA. So I wonder, are you planning to include the OTA releases again? Second question, it it possible to make the two step update process a bit...

BertB

I do not know the golden standard for the perfect ESP_Easy, sorry.

BertB

In the latest release, test_beta_ESP8266_4M1M is disabled as it is too big. Some of my WeMos modules use the Nextion plugin, which is still in TEST. This implies that I cannot update those modules, or is there another way? I see ESP_Easy_mega_20200703_test_ESP8266_4M1M_VCC.bin is still around. Can I...

BertB

Many thanks

BertB

Well, it has the following characteristics: ESP Board ESP Chip ID: 13281048 (0xCAA718) ESP Chip Frequency: 80 MHz ESP Board Name: PLATFORMIO_ESP8285 Storage Flash Chip ID: Vendor: 0x51 Device: 0x4014 Flash Chip Real Size: 1024 kB Flash IDE Size: 1024 kB Flash IDE Speed: 40 MHz Flash IDE Mode: DOUT F...

BertB

Okay, good to hear it is under control

BertB

It seems that the formula functuion in MQTT import does not work. I run: Build:⋄ 20107 - Mega System Libraries:⋄ ESP82xx Core 5473656e, NONOS SDK 2.2.2-dev(a58da79), LWIP: 2.1.2 PUYA support Git Build:⋄ mega-20200608 Plugin Count:⋄ 83 [Normal] [Testing] on a Wemos. I expect : %value%/1000 to give a ...

BertB

I would like to use a rev2 sonoff 4ch pro in a live situation, where it is very difficult to do regular updates.
Is it possible to use OTA for this device as well?

BertB

I have tested it too. Looks fine now.
Next I shal try this on my other ESP 32 devices.

BertB

Is this solved with the new release?

BertB

This is the cmd line: esptool.exe --chip esp32 --port COM4 --baud 115200 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size detect 0x00000 ESP_Easy_mega-20200426_test_ESP32_4M316k_factory.bin And this the result: ets Jun 8 2016 00:22:57 rst:0x1 (P...

BertB

Well, the programming of the ESP32 with the factory version did not lead to a working processor either.

BertB

Okay, I will give it a try, but it then is a different way to load the firmware. With this ESP32 I could always use the .cmd file containing: esptool.exe --chip esp32 --port COM4 --baud 256000 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size det...

BertB

I see. I will give it a try.
Thanks.

BertB

Hi, I have one ESP32 that worked fine up until ESP_Easy_mega-20200426_test_ESP32_4M316k.bin. I get this serial info: ets Jun 8 2016 00:22:57 rst:0x1 (POWERON_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:D...

BertB

Hi,

I have two ESP32 incarnations: ESP32-WROVER and ESPWROOM-32.
Both do not start correctly with any of the various ESP versions.
What can I use best?

BertB

Up to now, I used ESP_Easy_mega-20191003_esp32test_1M8_partition.bin for my Wemos with ESP-WROOM-32.
Which version should I use with the november 3 release?

BertB

By pushing the S5 switch untill all leds go green and off.

BertB

Great. You are much better at searching than me.
I spent for over an hour without result. Also on the Itead site. Perhaps because i was looking for the R2 version.

BertB

TD-er wrote: ↑21 Sep 2019, 13:38 Well, Sonoff does have schematics of their boards online, so you may want to check that to see how it is connected.

Do you know where?

BertB

I just flashed my fresh Sonoff 4ch Pro r2 with ESPEasy and had to disable all RF activity, as it disturbed things.
I am now wondering if it is possible to have RF 433 mHz control also active on this device. If yes, how can I pair the RF buttons?

BertB

the Sonoff is very stable the last couple of hours, so I think the 'problem' is solved.

I am only still wondering, if it is not possible to disclose the other sonoff functions as well.
With this I mean the timing sces and the 433 mHz controll.

BertB

I can Imagine that. I will test the sonoff in the weekend, but i think the issue is solved.

BertB

After erasing all coco devices, i had no more unintended switchings. Apparently the sonoff was paired off factory.
The sonoff has a 433 MHz receiver on board, but i do not yet use it.
Do you think this function can still work with the espeasy firmware?

BertB

I just discovered that one of my RF coco (kaku) transmitters actually also switched one of the relays on the Sonoff. I certainly did not pair the transmitter with the relay, so I think it was a left over from factory testing. So, I cleared all RF settings and it looks like all the previous problems ...

BertB

This is my rules script:

on System#Boot do
gpio,12,0
gpio,5,0
gpio,4,0
gpio,15,0
endon

on Button1#state do
gpio,12,[Button1#state]
endon
on Button2#state do
gpio,5,[Button2#state]
endon
on Button3#state do
gpio,4,[Button3#state]
endon
on Button4#state do
gpio,15,[Button4#state]
endon

BertB

4 and 5 are no longer assigned to I2C.
I'll see if I can make some kind of trap for the unintended triggers.

BertB

So far I can see, there are no reboots. The Sonoff is an off the shelve device. Here is the known GPIO list for the Sonoff 4CH R2: GPIO 00 - Button 1 GPIO 04 - Relay 3 GPIO 05 - Relay 2 GPIO 09 - Button 2 GPIO 10 - Button 3 GPIO 12 - Relay 1 GPIO 13 - WiFi LED GPIO 14 - Button 4 GPIO 15 - Relay 4 So...

BertB

No, that is not the problem. It happens when the device sits there.

BertB

20msec

BertB

Earlier this week, I flashed my fresh Sonoff 4ch pro R2 with ESP_Easy_mega-20190830_normal_ESP8285_1M.bin.
No problem here and I could also create some rules, so that a short push on a button, toggles a relay.

The problem I encounter is that some relays toggle unintended.

Is this a known issue?

BertB

[...] Most important update would be the migration to the non-test status. Well as easy as that sounds (removing a word "testing" and moving a define + updating documentation), it may be more difficult than you would think. As you may have noticed, the last number of builds were quite a b...

BertB

@BertB What do you think is needed to get it to "the next level" ? I can work very well with this plugin as it is. Maybe some more line would be nice to have. Sending data to a controller is not realy required. All event handling is taken care of in rules. Unless you want to fetch the dat...

BertB

I will think this over.

BertB

Various people worked on this plugin, based on the work of majklovec. ThomasB was the last person to make major improvements. Unfortunately it is still in the Test state and it realy deserves to go into the next level. Although I made the first rough version of what it is right now, based on the wor...

BertB

grovkillen wrote: ↑29 Apr 2019, 21:57
BertB wrote: ↑29 Apr 2019, 21:35 Interesting ... I only see an never stopping time wheel .
When does that happen?

With one of the WeMos boards. Right after clicking the Download UI button.
Another one did work, so I had a closes look.

BertB

Also the DUST sensor PMX X003 works very good.
I did not create it, but I would like to have it added to the Normal devices repository too.

Search found 772 matches