Let's Control It

Neoseb38

At the top, I just tested with wi-fi password deletion and after restarting, connection in AP mode then access to the page http://192.168.4.1/setup. Ditto if I delete the ssid, after restarting, connection in AP mode also then access to the page http://192.168.4.1/setup. On the other hand, if I make...

Neoseb38

Yes, that's it. Of course, I know that there is the solution of the serial port with the usb connection (so much simpler) but I assume that there are many projects based on esp32 where it remains inaccessible (swimming pool, tank etc...) This is the reason why the connection via AP remains the prior...

Neoseb38

To be forced to choose in the hardware / Preferred network medium tab and then reboot is a shame. Unfortunately, this is not what I had initially marked. I had ended the sentence with "is complicated", I would never have allowed myself to say that. The fault of Apple translation and not h...

Neoseb38

I just tested the test version you made me and how to say: It works perfectly! In wifi, I connect the network cable and direct I can connect in ethernet with the other ip. In addition, the speed is instantaneous during navigation. I unplug the network cable and direct it switches to wi-fi where I ca...

Neoseb38

IMG_5894.jpeg I used this post: https://community.home-assistant.io/t/how-to-add-an-external-antenna-to-an-esp-board/131601 The ESP32ETH01 has exactly the same integrated antenna as the first message of the tutorial. So I tried to apply myself and I used flux for welding. I also tested the good con...

Neoseb38

Otherwise, I had thought of passing the wired network through a carrier current...

To meditate

Neoseb38

The ethernet port is for my pool which already has a pulled network cable in my pool room.

For my father-in-law's, it will be in wifi and as already said, I will avoid putting too many devices on it.

For the range, it is not excessive and I soldered an antenna on the esp32 lol

: IMG_5892.jpeg (2.42 MiB) Viewed 1034 times

Neoseb38

I don't know if you had time to see: Thank you, I'll test all this tomorrow night. Yes, I remember well. .Bin for update and factory for the first installation. On the other hand, if this version works and the problem came from there, if afterwards I want to install it directly (without going throug...

Neoseb38

Then either load the web flasher page ( https://td-er.nl/ESPEasy/latest/ ) and press "Connect" (doesn't really matter which build you select) Then select the correct serial port in the pop-up window and continue. Then the web flasher page will show a white pop-up window showing the name o...

Neoseb38

Thank you, I'll test all this tomorrow night. Yes, I remember well. .Bin for update and factory for the first installation. On the other hand, if this version works and the problem came from there, if afterwards I want to install it directly (without going through an espeasy update) how do I do it o...

Neoseb38

These commands can be entered via the serial console (the web flasher page also allows you to open a console window, or use some serial terminal tool like Putty) or the "command" field on the Tools page.

How do we enter the esp32 once in the console or putty?

Neoseb38

: Capture d’écran 2025-04-15 à 21.41.59.png (116.17 KiB) Viewed 1065 times

Neoseb38

Thank you for all your new information and I take good notes. Or can I find the version you gave me at the time, if of course it is possible to find it? I would have liked to confirm that the problem comes from the firmewire version because if this is the case, it is much simpler since if you connec...

Neoseb38

So, It was very very laborious but I think I found it. I took everything back from the beginning. 1/ USB installation on one of the new esp32 eth01 2/ I didn't go through the usb for the wifi config but through the AP to test (it doesn't forgive because if there is a typo in the password either the ...

Neoseb38

Thank you :D I hope that for my part the non-SOLO1 version will correct the concern of losing the wifi network at each restart. PS: if I insist on the simplicity of change for wifi, it is because my father-in-law in a house is more than 2 hours from my house, and being over 75 years old, he knows no...

Neoseb38

Great, so to summarize, if the esp32 can no longer find internet after changing ssid (once at my father-in-law's for example) or internet cut, if I can't find the network (from the name of my esp32 in espeasy) on my phone, I unplug (I put an inter on/off in place of the jumper for the choice between...

Neoseb38

Thank you for your answer. I will do tests and cross my fingers so that the new version of the firmewire solves my problem. As for the AP mode, I was asking the question because on the SOLO1 version, it never appeared, not for lack of trying by cutting the internet etc... Sometimes you may need to p...

Neoseb38

Thanks again for your help. I thought my Esp32 ETH01 was an S1 version, who knows why :D I hope this is the problem and will solve all this. I'm trying tonight after work. For the update, I switch to ethernet and update directly under espeasy? I download this version in .bin? IMG_5889.jpeg If this s...

Neoseb38

Is the ESP still connected to Ethernet when you also try to make it connect to WiFi? No, only in wifi. Either in ethernet or in wi-fi, never both at the same time. I re-try for a good 2 hours but nothing changes. I try without going through the usb since in the future, it will be very complicated f...

Neoseb38

Thank you, it worked the first time and it was a power supply problem. On the other hand, I panic... Indeed, I installed everything on 2 new esp32 eth01 through the link you provided me and the adapter for usb connection. Wifi connections also via this link. Then, I restored my .tar backup (there to...

Neoseb38

Thank you, I'll try this way.
Can you tell me the exact manipulation to do with the gpio0 and the EN please?
I start with the gpio0 connect to GND then once turned on, I unplug?
For the EN terminal and the nest, do I just have to make a pulse?

DSL but I mix the brushes

Neoseb38

I spent the whole morning trying to install espeasy on my esp32 ETH01 but I didn't succeed. I had already struggled the first time but now I can't. However, I connected well like this: https://community.jeedom.com/uploads/default/original/3X/1/6/169875c0802c899a66f4fb631ccabc5bb79d9dd7.jpeg IO0 on h...

Neoseb38

Thank you very much for your very detailed message. When restoring on a new unit, the unit number and device name should be changed, and when using a fixed IP-address that must also be changed. The two esp32 will never be turned on at the same time. And since one of them will no longer be at my plac...

Neoseb38

Hello everyone, My project is coming to an end, and I am very happy. I finally finished the design of the 3d box and just like the pcb, it was a great first. I also left room for an evolution towards PH reading and therefore the module that goes with it. IMG_5871.jpeg IMG_5870.jpeg IMG_5869.jpeg At ...

Neoseb38

Hello everyone. I think I have made very good progress. On System#Boot do gpio,2,0 // État initial éteint let,100,10*3600 // 9h00 en secondes (pivot initial) let,100,[int#100]+30*60 // Ajoute 5 minutes let,101,60 // Constante pour le calcul let,102,100 // Pourcentage de filtration par défaut (100%) ...

Neoseb38

(I inserted 'All' before the trigger-time, as the day is part of the event.) Thank you very much for your correction. I Appreciate :D Glad you managed to find out stuff yourself. Sorry I have been extremely busy the past 2 weeks, which leaves not much time for ESPEasy :( I wish there was a way to h...

Neoseb38

I succeeded and I will have struggled a lot. The problem came from the temperature threshold of the level plugin that was set to 0. So every time I tried to activate my gpio2 also controlled by this plugin, it did not work since the latter turned it off every time since temperature above 0. So the r...

Neoseb38

I managed to make a little progress. I realized that the Variable V10 was wrong and did not correspond to the calculation. I searched on my side but I didn't understand. I ended up asking the question to different AI (not hoping for much) and only GROK to find, and the first time. Here are his words...

Neoseb38

Hi, did you have time to take a look at my total filtration problem of 1 second?
Yes, no, no worries, take your time. Thank you again for your help.

Neoseb38

The Tahoma is very good, it is superior but more expensive than the connectivity kit because it can control all Somfy devices such as blinds, lighting, velux etc... if you find it used for less, go for it

Neoseb38

Take the connectivity kit that works wonderfully with all Somfy protocols such as RTS and IO.
It's easy to set up and everything is detected.

Compatible with HomeKit etc...
I have it myself.

Neoseb38

Hi, I don't know if this is possible with your RFLink because the SOMFY IO protocol is very well protected. If you want to control your SOMFY IO blinds via Home Assistant, I recommend the Tahoma or, much less expensive (but still worth the price :D), the Somfy connectivity kit. Otherwise, there's th...

Neoseb38

OK Nothing to do with it, but: Is it normal that I have to wait at least 3 to 4 seconds to navigate to the ESP Easy web page (device to rules, etc.)? I'm connected to Ethernet (on Wi-Fi, I don't know why; it no longer wants to save the rules, whereas before it was connected to Ethernet, and you reso...

Neoseb38

Even with the corrected rule, nothing works.
I've changed the hour (and minutes

), but my relay remains off. In fact, it's impossible to turn it on (automatic mode or via command).

Neoseb38

Ah it is good I put that adjustment factor in a comment, as you have set it to 0, not 1.
So for now we just ignore it. Something for later when the rest is working.

Are you talking about that?

: Capture d’écran 2025-03-12 à 17.24.48.png (43.91 KiB) Viewed 4465 times

Neoseb38

just in case:

: Capture d’écran 2025-03-12 à 17.16.46.png (195.89 KiB) Viewed 4477 times

: Capture d’écran 2025-03-12 à 17.16.35.png (182 KiB) Viewed 4477 times

: Capture d’écran 2025-03-12 à 17.16.56.png (150.87 KiB) Viewed 4477 times

PS: I can't send anything in PM.

Neoseb38

Damn, I modified the rule to implement what we were talking about earlier. The rule I had earlier is the one you corrected by replacing the new tasks and values. Did I misconfigure my Regulator - Level Control (AdjustFiltration) (again)? Here's my new rule that doesn't work (I probably made a mistak...

Neoseb38

I just got home (I haven't changed the rules yet).
The variables have appeared, but the filtration relay is off.

: Capture d’écran 2025-03-12 à 16.22.18.png (57.78 KiB) Viewed 4502 times

I'll try the new rule in a few minutes.

Neoseb38

Thank you again, I assure you that I'm doing my best... my job is carpenter at the base 😂 I just do the temporary addition of your two lines (system boot) and the other two modifications and then I will only have to change the 14th of the pivot time for the desired time? Will it be necessary to do a...

Neoseb38

To simplify my tests, if I multiply let,1,[var#10]*60 to have timers in minutes, it would be easier, right? Let’s say I want to test between 6:00 PM and 7:00 PM. I would also need to reset, for example, at 5:50 PM (instead of midnight) and calculate the filtration time around 6:00 PM. Then, I set a ...

Neoseb38

Yes, I did 2 tests with temperatures 15 and 25 degrees and I find in result 3.5 and 9 which perfectly corresponds to the blue abacus curve (100%) of the beginning.
So it's a lot of hours and yes, you have to replace the initial calculation >10 because it's totally necessary (my fault)

Neoseb38

This is excellent news and a great step forward for my project 👏 I don't yet master the variables very well but I remember what you said for the differences between the Int and Var functions I'm currently at work and I'll see all this tonight. At the moment, 9 a.m. having passed, my relay will have ...

Neoseb38

The formula works and fits well with the blue 100% curve.
However, you have to keep all the numbers after the decimal points, otherwise the result in hours will be very different.
Do you think this formula is feasible for espeasy?

Neoseb38

You can also see the calculated variables #1, #2 and #3 on the system variables page at the top (only when they have been set) Nothing for the moment, I'll see tomorrow after 9am? To do this properly, I'll have to temporarily replace the pivot time calculation with minutes. Indeed, waiting several ...

Neoseb38

Wintering works since it's 22.2 at home and if I put 23 in Setpoint, the relay turns on. At 22, nothing changes (Hysteresis) and 21 it turns off. I think that given the time, it must also work because I can no longer activate my relay. (I reset the wintering to 0. When I activate the forced mode of ...

Neoseb38

I'm really sorry. I tried to replace the names that I changed in the code and I didn't see everything... I thought I was doing the right thing because it would be so much easier for me to find my way around and understand (with all this new information) As for the second level task, I misunderstood ...

Neoseb38

I renamed the task called "Temperature" and the task value "Pool" as you told me. Here is the rule: On System#Boot do gpio,2,0 // Éteindre la pompe au démarrage (sécurité) if [AjustFiltration#Output] < 0.5 OR [AjustFiltration#Output] > 1.5 // Make sure the "adjust" task...

Neoseb38

Wow, thanks again for all this valuable information. If I understand correctly, the regulator plugin will allow you to compensate for possible power outages, to do without a rule for wintering and also to be able to increase or decrease the filtration times? To do this, I need to create two "Re...

Neoseb38

But yesssss, it's not like you haven't repeated it to me... Capture d’écran 2025-03-11 à 06.40.58.png Like this? But what do I need to fill in for the GPIO and Device Settings (Input Task...)? Could you also explain to me roughly how your code works? I don't really understand everything. (I'm curren...

Neoseb38

In another post that was slightly drifting off-topic, TD-er provided me with a draft rule that I tried to update (Names and Values), as well as shorten the timers for testing. I also added screen displays to better see the plus and minus buttons, etc. However, I couldn’t get the code to work, so I’m...

Search found 122 matches