Difference between revisions of "ESP Hardware"
Jump to navigation
Jump to search
Grovkillen (talk | contribs) (Created page with "ESP Easy can be installed/flashed on nearly every piece of Hardware that has an ESP8266 built-in, newest 2.0.0 version even does support the ESP8285 (basically an ESP8266 with...") |
Grovkillen (talk | contribs) m |
||
| Line 1: | Line 1: | ||
| − | |||
| − | |||
This is a (not yet complete) list of Hardware which is known to be supported: | This is a (not yet complete) list of Hardware which is known to be supported: | ||
Revision as of 10:49, 28 May 2017
This is a (not yet complete) list of Hardware which is known to be supported:
| Device Name | ESP Chip | Flash Size | USB-TTL | GPIOs available | GPIO connected to onboard Hardware | onboard PSU/voltage regulator | Input voltage | Antenna | Size (LxWxH) |
|---|---|---|---|---|---|---|---|---|---|
| 12 E/F | 4MB | CH340 | 0, 1, 2, 3, 4, 5, 12, 13, 14, 15, 16, A0 (with Voltage divider) | 1&3 (serial) | RT9013 | 5 VDC (+/-0,5V) | onboard PCB | 34.2mm x 25.6mm x ?mm | |
| 12 E/F | 16MB | CP2104 | 0, 1, 2, 3, 4, 5, 12, 13, 14, 15, 16, A0 (with Voltage divider) | 1&3 (serial) | RT9013 | 5 VDC (+/-0,5V) | onboard ceramic/pigtail connector | 34.2mm x 25.6mm x ?mm | |
| WeMos D1 R2
|
12 E/F | 4MB | CP340G | 0, 1, 2, 3, 4, 5, 12, 13, 14, 15, 16, A0 (with Voltage divider) | 1&3 (serial) | 9-24VDC Switching power supply to 5 VDC(@1A) and RT9013 | 9-24VDC (power jack), 5VDC (5V pin) | onboard PCB | 68.6mm x 53.4mm x ?mm (=Arduino UNO) |
| NodeMcu V2
|
12 E | 4MB | CP2102 | 0, 1, 2, 3, 4, 5, 12, 13, 14, 15, 16, A0 (with Voltage divider) | 1&3 (serial) | ? | 5 VDC (+/-0,5V) | onboard PCB | ?mm x ?mm x ?mm |
| 12 E | 4MB | CP340 | 0, 1, 2, 3, 4, 5, 12, 13, 14, 15, 16, A0 (with Voltage divider) | 1&3 (serial) | ? | 5 VDC (+/-0,5V) | onboard PCB | ?mm x ?mm x ?mm | |
| generic ESP8266 | 1MB | None | 1, 3, (14) | 0 (button), 12 (Relay 10A@230VAC), 13 (LED) | on board mains AC to 5DVC + ? 3.3V Voltage Regulator Attention! The DC power is NOT galvanically decoupled from AC power! |
90-250VAC | onboard PCB | 88mm x 38mm x 23mm | |
| Sonoff TH10/TH16
|
generic ESP8266 | 1MB | None | 1, 3, (14) | 0 (button), 12 (Relay 10A/16A@230VAC), 13 (LED), 14 (AM2301) | on board mains AC to 5DVC + ? 3.3V Voltage Regulator Attention! The DC power is NOT galvanically decoupled from AC power! |
90-250VAC | onboard PCB | 88mm x 38mm x 23mm |
| Sonoff S20
|
generic ESP8266 | 1MB | None | 1, 3, (14) | 0 (button), 12 (Relay 10A@230VAC), 13 (LED) | on board mains AC to 5DVC + ? 3.3V Voltage Regulator | 90-250VAC | onboard PCB | ? |
| Sonoff 4ch
|
generic ESP8285 | 1MB | None | 2, (7, 8) | 0, 9, 10, 14 (Buttons), 4 , 5, 12, 15 (Relay 10A@230VAC), 13 (LED blue) | on board mains AC to 5DVC buck converter + 3.3V Voltage Regulator | 90-250VAC | onboard PCB | 145mm x 90mm x 41mm |
| Ai-Thinker A20 Breakout
|
generic ESP8285 | 1MB | None | ? | ? | ? | ? | SMA Connector | ? |
