Hi, I have setup rflink to my Home assistant and i'm able to receive RF commands like: [homeassistant.components.rflink] event of type command: {'id': 'aster_0004_01', 'command': 'off'} [homeassistant.components.rflink] entity_ids: ['light.aster_0004_01'] [homeassistant.components.rflink] passing ev...

>no answers from forum no answers from email no answers to help ... You send at least 4 messages about an elepowstar doorbel... and not all of them that friendly. You even received an answer that we are looking into it. >it s very unfair from the man/group who initiated this project to to drop thos...

The latest firmware release is from 18 OCTOBER 2017
The latest message on www.rflink.nl is from 23 AUGUST 2018

is the development and the RFlink board still alive?

Could be that i'm impatience and have to wait a bit longer

regards,
Passie

Stuntteam wrote: ↑20 Oct 2018, 09:48 The supported hardware is listed on this page: http://www.rflink.nl/blog2/wiring
There is no mention of and no support for the CC1101 at this time.

Any chance this will change in the near future, since this saves 15 euro?

Or I have missed it and you can already drive any 868 / FSK transceiver with RfLink , like the CC1101 ? No. Just to be sure since I asked a similar question. Should I/we be able to connect an CC1101 with RFLink instead of an Aurel? Crosspost: https://www.letscontrolit.com/forum/viewtopic.php?f=12&a...

Hi There, I'm trying to connect an CC1101 with an Arduino. I'm using the following schematics/connections, but i'm unable to get it working. Ground = Ground (VCC) = VCC 3.3 volt (MOSI) = MEGA Pin 51 (using level shifter 5V to 3.3V) (SCK) = MEGA Pin 52 (using level shifter 5V to 3.3V) (MISO) = MEGA P...

Maybe this post of mine will help.

https://www.domoticz.com/forum/viewtopi ... 8&start=20

Good luck

--- Passie

code is goed gekeurd en zit nu in 0.55, enjoy

Code is inmiddels goedgekeurd, Verwacht dat deze dus in de volgende release mee genomen wordt.

Dank je voor de snelle reactie. Ik kan ze nu uitlezen. Dus als ik via de afstandsbediening een rolluik aanstuur zie ik de up down en stop in de log. Als ik deze dan opneem als switch dan zie ik deze in de GUI als licht en kan ik on en off sturen maar verwacht eigenlijk up down en stop. Week u wat i...

Stuntteam wrote: ↑06 Sep 2017, 11:04 slowly making progress..winter is coming..

You are a season behind, winter is already here

any news on zigbee integration ?

Received my Somfy Rflink last week and it's working as expected. Though for some reason it's flooding my logs with the following. 2017-08-10 12:24:47 WARNING (MainThread) [rflink.protocol] dropping invalid data: 20;35;Debug;RTS P3;a0e20000dd; 2017-08-10 12:24:49 WARNING (MainThread) [rflink.protocol...

artic1980 wrote: ↑30 Apr 2017, 09:35 You can check it through domoticz

I'm trying to send the mqtt pub message not the integration with domoticz!?

I'm trying different pub's but i'm unable to get it working via mqtt mosquitto_pub -h 127.0.0.1 -t /home/candle/ -m "cmd=CANDLE:1:00FF00:100" Via a curl I can control the neopixel. set_candle_above: 'curl --data "cmd=CANDLE:3:FF0000:200" http://192.168.0.3/control' Any clue point...

Dylantje wrote: ↑27 Apr 2017, 09:56 Is this option available in the normal EspEasy flash?

No it isn't.

What is the complete mqtt message which has to be send in order to ex. change color ? Currently i'm able to send mqtt pub to easpeasy like so: mosquitto_pub -d -h 127.0.0.1 -t mosquitto_pub -h 127.0.0.1 -t /home/candle/Color/cmd -m 'FF0000' mosquitto_pub -d -h 127.0.0.1 -t mosquitto_pub -h 127.0.0.1...

Got the candle working via de esp web gui. Which command's should be send in order to control the light via mqqt from ex pimatic or any other home automation software ? I would like to control the led's with an if statement. So for example: If temp is > 20 celcius then make the leds red / flash. -- ...

They released the lights in the Netherlands as well.

https://tweakers.net/nieuws/123149/ikea ... rland.html

Would be nice if they could be controlled by RFLink out of the box ( with possible a firmware update )


-- passie

Any news on this ? Also wondering about the wiring, if you connect both transceivers to one mega, how does the rflink know to which pin to send if both transceivers are connected to one mega ? This page only explains 1 transceiver connected to the mega at one time. http://www.nemcon.nl/blog2/wiring ...

I don't see any line in the changelog regarding this ?
Is the current version of rflink already capable to handle both mhz on one mega ?

Passie