I already thought that it would be very difficult. The problem is that the balcony power plant does not feed in separately, but is simply attached to a phase. This means that there is no dedicated point at which only the electricity is fed in (electricity produced) and no point at which it is only c...

dear community, I have several pzem 004t V3.0 that work really really fine. There is no problem in stability - nothing, BUT... ...Now I have found that only the consumption is displayed, but not the direction of current flow. It is not possible to tell whether, for example, a photovoltaic system is ...

in the actual ESP Mega release there is no *energy file (ESPEasy_ESP82xx_mega-20201125.zip). I think at that time, November 2020, the Energy build wasn't defined yet. Oh I did a mistake. I took the wrong filename of the ESP mega release in the upper post. Now I'm writing over the cellular phone but...

ok I did find it just a few minutes ago

in the actual ESP Mega release there is no *energy file (ESPEasy_ESP82xx_mega-20201125.zip).

In the "old" release I did find the *energy file (ESPEasy_ESP82xx_mega-20210114.zip)

why it wasnt recompiled in the new release???

thanks in advance

I have not tested it myself. The only thing I did, was update the existing code from the playground to match the current code base and thus it should be functional identical, or at least do what the original code did + probably some more as added in newer code changed in the ESPEasy core. I was sea...

If you still want to build a NAS... I have done it this way: INTEL NUC 8i5with Proxmox - VM: OMV with Nextcloud etc dockered - LXC: 1. Grafana, 2. IOBroker, 3. motionEye, 4. dokuwiki, 5. piHole, ... 6-12 Watts of power consumption don't waste your time with raspberrys, if you have to run various app...

You are absolutely right. The 230V goes from 1,20m (light switch) to 1,5m without being connected. It will be connected in future if there is needed 230V. In my case i use 230V OR the Ethernet cable that also isn't attached. The KNX cable the same. Only piece of wire going into the light switch that...

Here we go with the pictures IMG-20210120-WA0040.jpg IMG-20210120-WA0041.jpg IMG-20210120-WA0045.jpg IMG-20210120-WA0046.jpg IMG-20210120-WA0043.jpg in every room I have the light switch at 1,2m and at 1,5m I have cat7 cable, 230V and KNX cable for maximum flexibility. Now I could install in every r...

hello guys, thank you VERY MUCH for you posts! That helps me really a lot. I am using iobroker, which gets all the sensor data via MQTT from the ESP8266 nodes. That runs perfectly. I save the data in an influxDB and the graphs are made from grafana. Thats perfect for me. Here you can see an graph fr...

How can i get them running? ESP easy has no support for this sensor and tasmota failed.
ESP home is too complicated to create the configuration in the jaml file

I thought about to wire up 8 SHT31 sensors (SHT35 cost 3 times as much as the 31 and are a little bit more accurate) on a I2C multiplexer Tca9548a on a D1 mini Pro. I think that could run safely. Now my question. Could 1 wire it up with an cat7 cable from the Multiplexer to each single SHT31... with...

I yesterday tryed to run the AHT10 Sensor with a self compiled binary of tasmota and tasmota recognized a totally different sensor. So I attached the SHT31 sensor and it runs out of the box with tasmota. So I don't know whats the problem, but with tasmota the AHT10 does not work. I bougt 2 of the AH...

oh sorry for that. i didn't know.
I read this and thought I had to do a PR if I whish support for AHT10 sensor

viewtopic.php?t=8049

I did open an issue. Hope this time I did the right thing

Thank you for your reply
I will test it and let you know if the functionality is the same

I have seen, that now following firmware exists:

ESP_Easy_mega_20210114_energy_ESP8266_4M1M.bin

Is the functionality the same as the version compiled from DJELAU?

Hello I use ESPeasy and I have AHT10 sensors and can not use them with ESPeasy. I've done a pull request on github... my first ever :-). https://github.com/letscontrolit/ESPEasy/pull/3465 I don't know if I've done it right. I would really appreciate if the AHT10 sensor would be added to ESPeasy mega...

Hi djelau, Thank you for your answer. I ordered other 5 PZEM-004T V3. I will test it, when the hardware arrives. I actually use a simple D1 mini, but will swap to the D1 mini pro to get an external antenna attached. The PZEM delivers 5V and I am not sure, if the D1 mini (pro) is 5V tolerant for a ve...

good morning @all @djelau: first of all: THANK YOU SO MUCH FOR YOUR WORK. I tried your firmware with one PZEM004T and it works like a charme. I get the values via MQTT into my ioBroker and its really fine. What I am thinking about is - how many PZEM004T could I connect to one ESP8266 (D1 Mini - whic...