Let's Control It

CoolRemote

Thanks to the excellent help here I managed to flash the Sonoff THR320 with the advised bin. file, for ESP32. The sensor added does not work yet, maybe because this bin. file was for the ESP32, not the ESP8266. It took a few times to make the flash work. The struggle is not exactly when to press the...

CoolRemote

Thank you for the help! Very much appreciated! Soon I hope to move on with this and happy to share the result.

CoolRemote

Basical it seems to point out that the bootloader is missing, and that it works with a bin version that contains a bootloader. Makes me wonder where I can download a factory version? I made a new account on Github, but did not manage yet to find the correct bin file. I must say I love Espeasy so far...

CoolRemote

I've been reading as much as possible about it, but I didn't read the thread you mentioned. Thank you for your input. At the moment of writing this post I went through the thread you pointed out to me and hope that will bring some new perspective.

CoolRemote

Recently I bought two Sonoff Origin's, (THR320). I decided to flash ESP Easy on the device. The flash went succesfully, however the device is not showing up after rebooting from flash mode. It does not appear in the list with WiFi networks. Because of this it is impossible to edit settings on the de...

CoolRemote

It seems that the RF doorbell set being sold at Action is compatible. That set cost about 5 or 6 Euro.

CoolRemote

After searching online for connecting a PIR sensor with relay and tamper switch to Domoticz by using ESP easy I found the following video; https://www.youtube.com/watch?v=6dz2qkyayLw . It seems to work, but no explanation at all and the text in the video is too blurry to work out what has been done,...

CoolRemote

Thank you very much for the input so far. And ofcourse more input and suggestion are very much appreciated.
In the past I added Sonoff's to my Domoticz and that is working fine. I hope the low voltage Sonoff's will do that too.

CoolRemote

Is it possible to also flash the 5v and 12v Sonoff modules the same way with the ESP Easy software? Like this one, please see the link below. This module seems also prepared for the RX/TX connector that can be soldered on the pcb. https://nl.aliexpress.com/item/Itead-Sonoff-SV-Safe-Voltage-WiFi-Wire...

CoolRemote

Thank you for the reply. I was expecting that it would reset the Sonoff's. They do not come back online in any way.
They also do not come online with their own setup as new installation.

CoolRemote

I have been building in a couple of Sonoff's. So far they were working fine. Today I have tried the new software version 2.0 and updated them OTA, but now the Sonoff's are not coming back online. Does that mean that I have to take all of them apart again to update them through the serial port by usi...

CoolRemote

Since a little while I got a part of Domoticz (finally) working. Thanks to the other forum members and others who helped with advise. I have a test connection and wait for my new RaspBerry Pi 3 to arrive one of the next days. As soon as I connect another PC, or reconnect something from the local net...

CoolRemote

Misschien zijn de batterijen van de buren leeg en word dat weergegeven?

CoolRemote

I had a simmilar problem. After all I took a another mobile phone not in use anymore and on that one I saw the ESP_0 network the first time.

CoolRemote

I have followed these instructions again and now it seems to join in with the same wifi network. I have access to both Sonoff's. Sometimes the LED is on and sometimes it is off. I don't know yet why. I have no access to the Sonoff's from Domoticz. That would be the last step to set this up I guess. ...

CoolRemote

Maybe it is down to the quality of these Sonoff modules? They respond very slow, after a reboot they take a couple of minutes to come back online. Besides that, if these modules are sitting (too) close to each other, can it be that they interfere with each other? I wonder if others here have the sam...

CoolRemote

If the flash was succesful it should not be defective. I had that idea too, until I got help from others here on this forum and it turned out that it was NOT defective.

CoolRemote

Heb ook gekeken bij Kruidvat, maar ze hebben ze niet en zijn ook niet in de aanbieding zeggen ze. Nu zeggen ze bij Kruidvat wel vaker iets. Misschien nog eens een ander filiaal proberen.

Klopt uberhaupt de genoemde prijs van 5 euro? De advertentie zegt 9,99.

CoolRemote

Have you tried to do the flash again? What is the result of the flash if you do this again? I have been succesful by following this "step by step" video and using the CH340 USB to Serial adapter. (No Arduino) https://www.youtube.com/watch?v=fN_QKOW ... ubs_digest

CoolRemote

I have been strugling with a simmilar problem. I flashed the Sonoff and followed exactly the steps provided in a video. However it didn't come back online, at least that is what I thought. I took another mobile phone and used a tablet and after a scan it showed up in the list. It might take a little...

CoolRemote

That is correct. However.....no matter if I edit this before uploading, or enter the details afterwards by having access to the Sonoff, and click submit, it does not change. In this example it does accept the name change for the Sonoff module Mod2, but not the SSID. http://i66.tinypic.com/hv1l6f.jpg

CoolRemote

For a little while I joined this forum too and found great help regarding several questions. Since I flashed the Sonoff I noticed that the SSID remains the same, ESP_0 or ESP_1, apart from the number that goes up with the amount of Sonoff modules that are in use/online. No matter what I try, that SS...

CoolRemote

Thank you Data. I managed to enter two Sonoff modules. In both I entered new credentials like SSID and new pasword. However the SSID for both remains ESP_0 and ESP_1, I confirmed all the steps with "Submit" which was accepted without any error. Also I did enter the other Domoticz details y...

CoolRemote

It took me a bit, but I am here and back with an update. Since the very first time it seems the flash was done correct and the Sonoff was working. I have been following the video I mentioned before and the flash was done correct and I could have done the setup of the Sonoff. However.....on the devic...

CoolRemote

vojtishek, I have been trying again and without succes. Wiring is correct. I am using two AA batteries at the moment since I did not manage yet to have the lab power supply ready, but when I read your experience it looks like that won't help either. A few posts back I have written down all the steps...

CoolRemote

While reading through your posts I think we come to the same conclusion that the lack of enough power (current) might be one of the reasons that flashing is not going the way it should go. But ofcourse there can still be other reasons too. I saw the link to the power supply, they go cheap indeed, ho...

CoolRemote

Insteresting information to move on with. I hope to give it a go again soon. I guess tomorrow and might use the lab power supply.
Will put updates here.

Enjoy your weekend and a Guinness

CoolRemote

Zojuist zag ik deze post en het is leuk om te zien dat dingen soms op de één of andere manier toch opgelost worden. Iedereen weer blij

CoolRemote

Thank you Nick-head. I have been following these instructions below, see link, to install the ESP8266 Add on. Including setting up the library the way they advise there. I am still wondering if the current might be an issue. Do you think that LED power supply can be used for this type of projects? I...

CoolRemote

Gave it another try. Used version R147. (Where can I download the version 78 you suggested?) No succes with uploading. Gives also problems with compiling. Can you please tell me if I have done one or more steps wrong in the steps followed below? That would be helpful for me in order to learn from it...

CoolRemote

At the moment I am only using the CH340 USB adapter or the Arduino, without extra power supply. This is one of the reasons too that I mentioned the extra power supply. However I don't have that but could order it. :) I might try another version too and will post updates here :) The first update for ...

CoolRemote

I opened Arduino. > ESPeasy. > I made sure that the COM port was selected, in this case COM3. > I have editted the SSID and the Password. > Next I clicked Save in Arduino. > Started Upload. > Connected the Sonoff while holding the button. > Released the button. > Clicked Upload. > Compiling was fill...

CoolRemote

@ Nick-head, I came with this idea incase I want to do other ESP8266 projects in the future once I know how this works, besides the Sonoff's. Also you see some mentioning that there are issues with not enough current going to the ESP8266. The Sonoff's might be up here, but they are no where to find ...

CoolRemote

Thank you all for your input. This is great! :D Possible I discovered something else what might lead to the solution. This might lead to a good laugh for some who have experience with this, but it is new for me and we all need to learn this and that takes time. I added NO credentials at all to the s...

CoolRemote

Those boards are interesting indeed. I guess if it is used for projects like Domoticz that they work fine, and they safe a lot of space and energy. Maybe add an extra Sonoff to turn the Banana Pi on and off :lol: I wonder if this power supply, being sold as a LED power supply, and with build in EMI ...

CoolRemote

The Banana Pi has a Gigabit LAN connector. Also it has a SATA connector. From what I have seen the RaspBerry is starting up a few seconds faster.

CoolRemote

I lost my software already, for me that information came too late. :( Besides that, I also would love to set up a good working Domoticz. I have set up Domoticz on a test pc and have been playing around with it to see how it works. So far that is working fine. Now the Sonoff modules to complete it. S...

CoolRemote

Maybe your soldering skills are better than my software skills. But that is why we can help each other. 120mA is not a lot, but maybe enough? I found also this link (Dutch) how to make a backup from the original firmware. When I do this again I might do this step first: http://domoticx.com/esp8266-w...

CoolRemote

@ vojtishek, It looks like you could have used a tiny bit more solder on those contacts in order to avoid connection problems. Make sure that it flows out around the contacts really well. Apart from that it looks fine.

CoolRemote

Maybe it is Data. Thank you for the suggestion. A few details I noticed have been marked. A few people convinced me that the Sonoff's are not defective because of these issues. Below a part of the code. (The network name has been replaced for "Network-SSID). Even if COM10 is selected in this ca...

CoolRemote

After a day trying and trying I am unable to find the solution. I keep getting error messages.

warning: espcomm_sync failed
error: espcomm_open failed
error: espcomm_upload_mem failed

CoolRemote

Thank you very much for the help. I have been trying to flash the Sonoff with the Arduino UNO, without succes. Also I have been trying again by following the video mentioned and also that failed. Arduino makes clear that compiling goes fine without any problem. I didn't know the correct amount of th...

CoolRemote

Thank you very much Nick-head, Each single bit of help or information is welcome. So I guess the Sonoff's are not defective but just hard to find online?

CoolRemote

I am not sure, there are the 512, 1024 and the 4096 in the same folder. Where can I find the files to clear the Sonoff? I have been following the exactly the instructions in this video: https://www.youtube.com/watch?v=8CuD6YBdACs >> I have tried a second Sonoff module. Have done the flash, and the r...

CoolRemote

I used the version R120. Strange enough it does not start it's own WiFi network like "ESP_0"
I just wanted to try to upgrade it to the R145 version. On that I get the following error: stat ESPEasy_R120_1024.bin failed

CoolRemote

I have bought 4 Sonoff modules, the version with WiFi only. Today I decided to use one of them and flash them with ESPeasy. The result is that the module does not create a new WiFi network, also the LED does not turn on. The flash went fine, no problems there, but once the flash procedure is done it...

CoolRemote

Hallo, Ik heb mij zojuist aangemeld op dit forum omdat dit topic aansloot bij wat ik eigenlijk ook naar op zoek ben momenteel. Kan iemand bevestigen of dit ook werkt met de "Impuls" set van de Action? Ik heb de meest recente versie van Domoticz zover ik na kan gaan, net gedownload en geins...

Search found 47 matches