Hi to all,
the same question ? Some help.
Thanks

+1
and or TX power in dBm...
Regards

+1
Regards

Hi JR01, Excellent blog, very accurate description of what you've been through, and exactly what I'm going through what I believe everyone else. (Who are just entering the world of M2M protocol) ... So after a few months of reading I came to the same conclusion and see that the image is formed as it...

Hi to all, ESP easy I loved from the beginning,offers many unimagined solutions,customizable for everyone. Many experiments I have done many times was pleased with the wide possibilities of this project. However, back and forth everywhere appears as almost the best solution MQTT ...Here I'm a bit st...

Hi all, Hi Alen, understand your interest in opening the garage door via ESPeasy and because yours question contains a question regarding the hardware you've got a very fair and accurate answers and I also agree with everyone, however, perhaps this is a good place for another question ... Do you wan...

+1
Regards

Hi, I see a lot of desire related to the various controllers and platforms. Interested me after I did some experiments and like the solution for some things on " Blynk ". Whether this option is accidentally dropped, or has some other (technical) reason. Blynk after promptness and presence ...

+1
Thanx

Of course, gladly, just to test ESP01 and NodeMCU V1 module and SSR 5V DC because the PCB supports them. ... Also in preparation is a PCB with the new development of the ESP Easy possibility to have a external WD timer and WiFi status LED position. I have reason to do extensive testing for eliminati...

My first PCB on the subject ESP...PCB supports multiple ESP module versions, multiple versions of power ... and we'll see what direction will go the development... WD next ... https://www.facebook.com/photo.php?fbid=908344435929451&set=a.908344189262809.1073741827.100002617080056&type=3&...

Thanks for the prompt reply. I hope that you will succeed in doing so. I have the experience that high output RF emissions very often tends to be a big problem and can affect the selectivity of the receiving part, especially if ESP is not far from the AP or other devices or when the crowd in the air...

I use the Arduino IDE 1.6.8 with board manager v 2.0.0 to program the ESP8266 Using the following commands to set the requested wifi settings: wifi_set_phy_mode(PHY_MODE_11G); system_phy_set_max_tpw(powervalue max 20.5); WiFi.mode(WIFI_STA); Thanks :) It's just that I have used for encryption 2.1.0...

Thank you. Solved since version:
#54 - HTTP Authentication on Domoticz (R85)

B: Put the ESP in 802.11G mode instead of 802.11N mode. I think the Rf spectrum will be less in G mode.
C: Put the ESP in wifi STA mode only.
D: Lower the ESP wifi output power to 10dBm.

Where these settings?
Thanks

Very likeable and eye pleasant custom CSS ... Small asking after installing IFTTT maker were a little short windows for "Identifier"
Thanks

Very good plugin...Thanks...Works, nice job.
Congratulate.

I thought about that IFTTT works fine ...

Excellent function nicely work .... Just one question that comes to mind whether to have two kinds of login, such as user login and admin login for example, that user can only configure wifi and with admin login all other functions & configurations...,perhaps and that the advanced panel has a ki...

Part one (collection/ list ) My proposal is to insert in the analog readings sample / average option. Reason: Nearly all analog sensors suffer from low immunity to RFI / EMI noise and other interference, especially if our devices get out from the experimental phase. In the industrial electronics is ...

Respekt costo,
Thanks for the suggestion that way I will do.
All the best.

I'm a little sorry that no one comment on the suggestion / question. I'm not saying that the suggestion was a revolutionary or a good but as I said, if we consider that UART should probably remain, two pins for I2C bus, if we add that the GPIO pins 0 , 2, 10, 15, conditional and for other functions ...

Dear costo, maybe I was not clear enough, or you may missed the point ... It is about the fact that there are serious branded machines with alrady built-in NTC thermistors and what is more important they are sometimes difficult to mechanically interchangeable or glued/ sealed in a mechanical assembl...

Hi to all Somewhere in the forum I found that lists of wishes does do not extend to sensors that already exist in several forms, for example, thermal sensors ... But NTC Thermistor are still widely used in various devices, especially in refrigeration and air-conditioning ... Sometimes it is not easy...

Hi
Work on version 91/92 LCD2004
at mine
RSSI:[Sys.info#RSSI]dBm
RSSI:[Name#Values]dBm

Hope to work for you.
Regards
Petko

Identical experience...

From day to day miracle worker of the project progress and processed each day and the project becomes bigger and bigger. Of course there are a wish list and requests for the status LED, traffic(already implemented) ... After key lcd / oled... I thought that slowly consumes resources (which are relat...

Congratulations to the latest version, I think on the authentication to Domoticz server,works flawlessly.

Yes JAN , Domoticz server require a username/password if you not input IP for local networks in settnigs of Domoticz...So right question is can anyone to help me to made changes in _C001.ino that ESP-Easy send user/password to log in Domoticz...I hope you understand me.... User/pass needed because a...

Test 2: If in the settings of domoticz server enter the IP address of the remote location then ESP-Easy working completely normally on port 8080 without NAT and port redirects in the router at a remote location ... So the conclusion is that everything is working from remote locations but due to dyna...

Thank you to JAN, is really the answer I was looking for. Thanks for the tutorial proposed but like I said everything I read and tried and everything works in the local network just hoping that there is compatibility between the Domoticz server and ESP Easy on port 6144 for which you have said that ...

Thank you for taking the time that you have to answer my question, but until I progressed in my knowledge of internet communications to simplify the question .... Do in each location where I have esp easy I must to have a Domoticz server configured as a slave or ESP-easy can work independently like ...

Hello,esp easy is awesome and all congratulations on the project. As a beginner I have one question .... While everything was working in local network, everything was fine .... Because I want to have more esp easy module at various locations I put Domoticz on a static/public ip address but from ther...