Let's Control It

bastler11

I will have a look on it, thanks.

bastler11

Thanks, I will have a look on it. Actually I built a housing for the sensor and tried to make it close against humidity, because it is direct over the filler neck. The water level is in 30cm. To open the housing it is a little difficult.

bastler11

Ok, then I must order some. So if I have an esp32 I could use the rule like I tried to do? It is not so urgent, I want to have an additional check for the water level of my greenhouse watering tank. The actually esp2688 is still build in a small housing, to change the hardware, I think I have to bui...

bastler11

Thanks, so which build should I use?

bastler11

Hello, I use an esp2866 with the actual firmware. I measure the distance with a time of flight sensor VL53L1X. From the value of this sensor I want to calculate the average value. In the rules I tried to use this: On Tank#Wasserstand Do TaskValueSet,AverageCalc,Wasserstand_gemittelt,[Tank#Wasserstan...

bastler11

Yes, it is not so big, but I thought it better than the OLED SSD1306? On the other side it is a little bit expensive.

bastler11

Thanks, now it works

bastler11

I had a look on this board:

https://www.amazon.de/dp/B0CRYJC3NW/

One more question: how could I get an information that somebody answers on my question, is there a switch in the settings?

bastler11

Hello,

would it be possible to run and ESP Easy on the LILYGO T4-S3 ESP32-S3 board and control over ESP Easy the display?

Thanks and best regards!

bastler11

First of all, thanks Rob73 and TD-er for your ideas. I´m late but I was a little bit busy the last days and the delivery for the Hall sensors needed also some days. Today they arrived. I exchanged in my test environment this: ESP8266 -> ESP32 and reed contact -> Hall sensor. The result is really so ...

bastler11

Hello, I tried to build a pulse counter for my anemometer. For this I build a test environment. IMG_5656.JPG I use an esp8266 with normal 4M VCC firmware. I connected a 10kΩ resistance between ground and D5 and a reed contact between 3V and D5. The reed contact I fixed near the chuck of my lathe. Th...

bastler11

Hello Andrzej,

good idea! How did you connect the JSN-SR04T to the ESP? Did you use any converter for the Signal for 5V to 3,3V?

Thanks and best Regards!

bastler11

Thanks, this I didn´t saw. Here are the info about the memory. It seems that there is enough, or? If I try to upload the esp.css it begin to upload and then the screen is empty. It look different to the other files. There comes after uploading the information to reboot.

What can I do?

bastler11

I tried it again to upload all files, without any success? What can I additionally do?

bastler11

Thanks, I tried to upload all files (also the renamed file, but it is still the same problem there?

bastler11

Hello,

I tried to change a display on my esp8266 (from 0,96" to 1,54"). After changing the web interface look different? I tried to make a firmware update, but it does not work. What can I do?

Thanks and best regards

bastler11

Thanks, if I use "Step through frames with Display button". I have this configuration. Screenshot-Aug.-13-2023_09.49.29.jpg If I tap the GPIO to ground the shown value is either distance or voltage. But if the value changes for example from 10mm to 50mm on the display nothing happens. I ha...

bastler11

In the moment I use 2 input signals, the value from the analog input and the distance. Both are showing one after the other. How could I switch with a contact between both values? GPIO X on ground -> value distance, GPIO open -> analog input?

bastler11

Thanks, it works!

bastler11

I have one more question.

I have an other ESP8266 with an OLED SSD1306 display and want now to connect a VL530X sensor, to show the distance value on the display. How do I connect the sensor to the board?

bastler11

Good morning together, I disconnected the power of the ESP and the values are there (ambient and waterlevel). :) What I remarked, when I set "Send event when value unchanged" the water level value is a moment "0" after closing the edit page. When I disabled "Send event when ...

bastler11

No I did not, the sensor is outside in the garden and now it is dark. I will try it tomorrow. But I tried to flash with the old firmware from 2021 and that is working, the values are there. Than I tried the new firmware again, but the TOF sensor still does not work. So could disconnect the power bri...

bastler11

Seems that there is still a problem - Check I2C devices is enabled - the TOF sensor could not enabled. After switching of I could it enable but shows no values

bastler11

I just load the file from Github. After rebooting, there was no value. Then I set the time to 1 sec. and it works. But after enabling "Check I2C devices" it is again not possible to enable the VL53L1X. Then I make a reboot and the in the device overview you could see the enabled VL53L1X. B...

bastler11

Thanks for the information, I will try it in the evening and will report!

bastler11

Thanks, hope it is not too much work

bastler11

I disabled that setting from Tools/Advanced: Check I2C devices when enabled.

And now I could enable the sensor and it shoes also values. So is there any bug in the plugin?

bastler11

Thanks for reply. I think there is a mistake from my side :oops: . I have the VL53L1X and not the VL53L0X. I just tried to install the actual Collection B with and without VCC. In both cases the sensor (VL53L1X) is first enabled and the values are 0. If I try to edit any thing (change the time from ...

bastler11

Hello, I use the GY-530 VL53L0X Laser Ranging Sensor Time-of-Flight. The firmware on the ESP I use is from 2021 a "Test" version. Now I tried to use the new Collection B. If I flash the ESP the sensor is available, but there is no value. Also after a reboot. If I flash it back to the old v...

bastler11

Ok, than I have to change to ESP32.

Thanks again!

bastler11

One more thing

.

I tried to use this function with an other device. But there I do not find the Stats checkbox. Do I have to update the firmware?

bastler11

Thanks!

bastler11

No do not work. Were do I find the value Prozent.avg

bastler11

I do not understand? Here are again some screenshots.

In the rule you send me: TaskValueSet,ZisInhalt,Dummy,[Zisterne_Inhalt#Prozent.avg] were have I to write it?

bastler11

I deleted all rules and all Dummy Devices. Then I and wrote the rule for the content new. But the shown value is still 0.0?

bastler11

Thanks,

I tried to do it, but values will not be shown?

bastler11

Hello, I use 4 sensors with my ESP2866. One signal is not very stable, so I tried to use rules to get a stable value. But It does not work. The average value I got is about 74 instead of about 102? Here are some screenshots. Could you have a look on it? What is my mistake?

Thanks and best regards!

bastler11

It works fine now, thanks again!

bastler11

After I disabled all tasks, I could install the modified firmware and now I could see the options for the multiplexe!

Thanks for all!

bastler11

Thanks, I will try it tomorrow and will report.

bastler11

I took also an other browser, the same result? It is not the first time that I flashed an ESP.

bastler11

I made exactly that what you wrote. The file I use has the correct characteristic (date 10.12.). It seems, that the file will not be written? But there is no error message? After I click Update the Firmware, it needs some minutes and then it starts again.

bastler11

I tried it again 2 times, there is still the file from 05.11?

bastler11

This is the content, I installed the 1. file

bastler11

I looked first at the hardware page, there is no TCA9548a to select?

bastler11

Hm, I flashed the ESP with your firmware, but in the menu I find no I2C Multiplexer option? Or will it only appear when I connected the multiplexer?

bastler11

Tanks very much! I will report. The multiplexer should arrive during next week.

bastler11

Here I found the document:

https://espeasy.readthedocs.io/en/lates ... dware.html

On the hardware tab I do not find the settings? Where do I find what build is "LIMIT_BUILD_SIZE" and what not?

bastler11

Thanks, I ordered the multiplexer. On the hardware page I found this: "Since build 20110, there is the option of using an I2C multiplexer. This option is not available in all builds, because of the size of the code. It is usually available in the normal, testing and custom builds, but ommitted ...

bastler11

Hello, I tried to connect a second OLED displays (OLED SSD1306/SH1106 Framed) to my ESP8266. I used also D1 and D2. First I didn't wrote any content in the second. Both are running, but they show the same. Then I wrote in the second in the first line a content. Now this contend is scrolling in the m...

Search found 110 matches